The Wall Mounted Banner Pole System comprises of a heavy gauge aluminium pole to which the banner is sleeved and connected to the wall. From standard to self-tensioning both available with single wire support depending on the circumstances and application.
The Standard Wall Mounted Banner Pole System is ideal for your basic banner system. The system comprises of:
- 2 off Heavy gauge aluminium 27mm diameter poles, mill finished (silver)
- 5mm Wall thickness for strength
- 2 off Electro-plated (silver) steel back-plate/spigot
- Back-plate size 75mm wide, 130mm long, 5mm thick
- Projecting spigot 100mm approx.
- Back-plate pre-drilled, 4 holes M8 size
- 8 off M8 70mm Sleeve anchor bolts
- 2 off Galvanised locking pin
- 2 off Plastic collars
- 2 off Plastic end bungs
- Neatly boxed with fitting instructions included
The Self-Tensioning System helps to deal with expansion of PVC due to wind and heat. The 'slap' factor which is a result of wind and heat is alleviated when the Banner is Self-Tensioned. The banner system is easy to install and adjust.
Banners using this self-tensioning method have to be made in a special way. We will gladly quote you for a blank banner or a digitally printed banner or finish your preprinted banners to this specification when being fitted to this system.
System comprises of all the Standard System plus:
- Stainless steel 12mm rod
- Galvanised tensioning hooks
- Heavy gauge springs
- Nylock nuts
Maximum recommended banner sizes for above systems
455mm wide x 4.5m drop
610mm wide x 2.5m drop
760mm wide x 1.75m drop
915mm wide x 1.0m drop
It is important that a qualified engineer assesses the suitability of all the above structures to withstand the additional wind loading created by the installation of any of these assemblies
Single Wire Support Kit
Making poles stay horizontal gives additional support and adds to the life and better presentation of the banner.
Our Wall Mounted Single Wire Support Kit top and bottom comprises:
- M10 Eye shield anchor bolts
- Thimble Eye Wire with attached rigging screw
Heavy Duty Twin Wire Supported System
The Heavy Duty Twin Wire Supported System is based on our very successful banner pole system and takes the strain out of fitting big banners up to 6m x 1m.
The system comprises of all the components of the standard or self-tensioning banner poles plus:
- 2 off 27mm diameter aluminium poles to suit 1 metre wide banners
- 6 off M10 Eye shield anchor bolts
- 2 off ‘D’ shackles
- 4 off Thimble eye wires with attached rigging screws.
Can be supplied as standard or self-tensioning.
Heavy Duty White Powder Coated Wall Mount Banner Pole Systems
We have made the installation easy by the elongating holes in the brackets so tensioning the banner becomes simple. Maximum recommended banner size is 2m sq
2 Pole widths available: for up to 500mm and up to 800mm wide banners
Each kit consists of two steel brackets with elongated slots and fully welded arms to make fitting and tensioning the banner easier than other systems on the market, all brackets are etch primed and powder coated standard white (other colours can be catered for please ring one of our sales team for a quote).
Extra Heavy Duty White Powder Coated Wall Mount Banner Pole Systems
This system is constructed from fully welded steel brackets 200mm x 300mm square backing plate with 60mm diameter steel arms.
We have made the installation easy by the elongating holes in the brackets so tensioning the banner becomes simple. Maximum banner size is 5m square with stay wires.
3 Pole widths available: for up to 500mm, 800mm and 1000mm wide banners
Each kit consists of two steel brackets with elongated slots and fully welded arms to make fitting and tensioning the banner easier than other systems on the market, All brackets are etch primed and powder coated standard white (other colours can be catered for please ring one of our sales team for a quote).
If you are unsure of the structure you are fixing the system to always consult a structural engineer.
The above systems are available with extra tensioning kit.